|
|
|
 |
DD-2
|
| |
SPECIFICATION |
| INSTRUCTIONS:- |
Thanks for purchasing Roxy Model DD-2, in order to make the best use of DD-2, please read the following carefully.
|
|
|
| |
| FEATURES:- |
DD-2 is a delay Pedal effect, which has two types of delay made (400ms/800ms). With simple setting of Feed Back and delay Time to create vintage delay sound. Use Level control to mix the dry and wet signal connect output A/B for stereo use.
|
|
|
| |
BATTERY REPLACEMENT:- |
1.
2.
3.
4.
5. |
Loosen the screw on the pedal to open it.
Remove the battery compartment and disconnect the battery cable.
Connect a new battery to the battery cable and put it back in the battery compartment. Make sure he polarity of the battery is correct and the battery cable does not interface with the spring or pedal cover.
Push the coil spring in the base. then close the pedal.
Insert the thumb screw into the guide bush hole and firmly tighten the screw. |
|
|
| |
IMPORTANT NOTES :- |
1.
2.
3.
4.
5.
6.
7.
8.
|
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heal sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Protect the power cord from being walked on pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.
Unplug this apparatus during when unused for long periods of time.
No user services part inside. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply card or plug is damaged, liquid has been spilled or object have fallen into the apparatus, the apparatus has been dropped.
| |
|
| |
PANEL DESCRIPTION:- |
1.
2.
3.
4.
5.
6.
7.
8.
9.
10
|
AC Adaptor Jack Connect and AC Adaptor (100-240V/50-60Hz)
Ar AC Adaptor allows long and secure operation without worrying about battery life. Use the proper supply for your area’s Mains line voltage.
Indicator LED. This LED indicates when the LED becomes dim or does not light the battery need to be replaced.
Level Knob : Used this control to adjust the output level of the effect.
F. Back Knob : Use this control to adjust the feedback level.
Turn this knob clockwise to increases the amount of the sound is repeated.
D. Time Knob : Used this control to adjust the delay time. The Delay time can be changed with the setting rang.
Mode Knob: Use this switch to have a good commend of the delay time mode. Include both of 400 ms and 800ms.
Output Jacks A (MONO) B: Use these jacks to connect an amplifier or other units. Use Jack A for mono output.
Pedal: Press the pedal turns the effect on and off.
Thumb Screw: Loosen screw to open the pedal for battery replacement (For detail of the battery replacement, see “BATTERY REPLACEMENT”)
Input Jack : Connect your instrument to this jack. To prolong battery life, disconnect all cables from the pebal when not in use
| |
|
|
| |
CONNECTION:- |
1.
2.
3.
4.
5.
|
1. Connecting an Instrument to this jack will automatically switch the unit on. Be sure to disconnect the cord from this jack when the unit is not being used.
2. Before connecting or dis connecting any instrument, make sure that the volume of the amplifier is turned down.
3. For monaural output , us Output jack A Both the dry and processed signals are output.
4. For stereo use : Output A: Only the processed signal (pitch modulated sound) is output. The dry (unprocessed) signal is not output. Output B: Only the dry sign-al is output.
5. When you us a high output guitar, the sound may be distorted. If distention occurs. turn down the volume of the guitar or use a limiter, etc.
|
|
|
| |
|
|
|
|
